Remove foreign objects from rear tray - MG5120

Check for Obstructions in the rear tray

If paper does not reach the Paper Edge Sensor, the LCD will show [Rear tray.

There is no paper. Load paper and press OK].

Power off the printer.

Remove paper from the Rear Tray.

Look in the Rear Tray area for an obstruction. If there is any foreign material (such as a piece of metal or pen) inside the printer, after turning the printer off and removing the power cord from the outlet, remove the foreign material by hand, or with tweezers.

Open the scanning unit (printer cover) and confirm that there is no foreign material in the printer. If there is any foreign material, remove it.

Note:
Avoid touching inner parts.

Close the scanning unit (printer cover).

Note:
When closing the scanning unit (printer cover), be careful not to jam your finger.

Power on the printer and confirm that the printer operates normally. See More ( )

Request for service

CALL US +1-855-517-2433  (TOLL FREE)

Reset the printer to resolve error conditions or if the printer does not respond

Resetting the Printer

By resetting the printer's power, the print buffer is cleared and certain sensors are reset. If there is invalid data in the buffer, or sensors are stuck in a particular mode; a message may appear.

Follow these steps to reset the printer:

Turn the printer off with the Power button (if available).

Disconnect the data cable from the printer (not applicable to WiFi, Bluetooth or Infrared) .

Unplug the printer's power cord for approximately 10 minutes, and then plug it back in. If troubleshooting a communication issue, reconnect the data cable (not applicable to WiFi, Bluetooth or Infrared).

Turn the printer back on.

Note: If resetting the printer does not work, please attempt any other solutions that appeared in your search results. If this is a hardware message on the printer, the printer may need to be repaired. See More ( )

Request for service

CALL US +1-855-517-2433  (TOLL FREE)

Printers - Canon BX Fuser Measurements

if you measure values in the indicated range on the right hand side of the fuser, the lamp is fine (240V fusers will read 3-4 times higher on the right hand side

Models
HP LaserJet 4V/4MV (Check uur cross reference guide below for other brands)
Removal Instructions
Open the front of the printer. Pop out the charge transfer roller, being careful not to touch the surface of the roller. Handle it at the metal ends only. Remove the 5 big brass screws holding the fuser in. There is a screw at each lower end of the fuser. At the top of the fuser, you'll see 5 screws. Remove the 2 outboard and the center screws. While pulling out on the plastic side to clear the metal shaft, lift one end of the fuser up, repeating for the other end.


If you don't have a meter, continuity can also be checked across the contacts on the right hand side of the fuser by using a digital tester.

Cross Reference Guide: Canon BX Printers


Acorn Graphtex 400
Apple LaserWriter Select 350
Birmy Graphics Powerimage 11/17, XL 11/17
Brother HL-8PSJ/HP-PSJ
Calcomp CCL600/XF
Canon BX
Canon LBP-BX
ECRM Scriptprinter
Genicom Corporation 9080
Daikin Industries Comtec 9700+
Intergraph Corp-8ppm
JBCC Power Writer 5036
JRL Systems Easycopy L Series/LP-180
Newgen Sys Turbo PS-440B/660B/1200B
OCE 6450/6451/6460
QMS 860 Hammerhead Print System
QMS 860/860 Plus Print System
Varityper 5160, Panther
Xante Accel-A-Writer 8100/8100 ENH
Xitron Clipper Cadet
Read More...

Any Kind of Canon Printer Problems Call Us
+1-855-517-2433 (Toll Free)

How to Install Canon Printers Without the Disks

canon printers are more commonly used for personal computers, as opposed to commercial use. These particular printers usually come with installation disks that are used to install the hardware's software drivers on the computer, but it's easy to misplace those disks over time. Luckily, the Canon support site provides software drivers for Canon printers, allowing users to install the software without the disks.



1 .Go to the official Canon Global website in your computer's Internet browser.
2 . Click the "Support <Drivers/Downloads>" tab along the left side of the Canon Global homepage. Select your region on the interactive map that appears on the right side of the tab options, and select the subregion where you are located.
3 . Select your product type, and click "Printers & Multifunction" to begin searching for your Canon product type. Click the product series that relates to your Canon printer.
4 . Scroll through the list of Canon printer models in the product series. Click the "Drivers & Software" link next to your Canon printer's thumbnail image. You will be redirected to the printer's product and overview page.
5 . Scroll down the Canon printer's product and overview page to the Drivers and Downloads section of the page. Click the "Select Your Operating System" drop-down bar. Select the name of your operating system, and click the red arrow to retrieve the software driver for your system.
6 . Click the .exe link under the firmware files that will be listed for the Canon "Software & Drivers" section.
7 . Run the Canon printer driver's .exe file from the File Download box that will appear. Click "Open" once the driver is processed. This file download will open the Canon installation wizard.
8 .Follow the system prompts in the Canon installation wizard to connect your Canon printer and complete the installation process. 
Read More...

Any Kind of Canon Printer Problems Call Us
+1-855-517-2433 (Toll Free)

How To Service My Printer - Error Code for Canon PIXMA MP287

P02 – Carriage Error, there is something wrong with your printer ink cartridge, it could be in wrong position, something blocked the chip (see at the back of cartridge), also P02 error code show sign that your print head is broken or faulty, try to take out both of the cartridge and then put it back.

Read More...

P07 – Ink Absorber Is Full or Almost Full, you need to reset your printer, here is an article how to reset your canon mp287 printer. Follow the step, you can reset only if your absorber is almost full. You can’t reset if your ink absorber is full, to fix the absorber is full, you need to disassemble your printer and then replace the ink absorber (it’s just a pieces of sponge located in the printer), last time I just deep the sponge into water until the sponge is clean. I found a video but for MP258, the sponge located at the same position.

Read More...

Any Kind of Canon Printer Problems Call Us
+1-855-517-2433 (Toll Free)

How to Reset Error Code E08 in Canon MP287 - Absorber Full

When the MP287is turned on, it will immediately appear on the LCD panel error E08 MP287. And when we do print command, then the monitor screen will show “The Ink Absorber is Almost Full”. Caption MP287 E08 error on the screen as follows:

1. Turn on the Canon MP287, MP287 LCD then the panel will pop up error E08, and there is a description of “The Ink Absorber is Almost Full” on the screen of your monitor.
2. Download Resetter MP287 at this link
3. Canon MP287 printer must be in a state of SERVICE MODE. Do I read the next step.
4. Canon MP287 Turn off the E08 error by pressing the power. Do not unplug the power cord.
5. Press and Hold the button STOP / RESET followed by pressing the POWER button. So both buttons depressed position.
6. Release the button STOP / RESET but do not release the button POWER.
   Read More...
   
   
   
   Any Kind of Canon Printer Problems Call Us
   +1-855-517-2433 (Toll Free)

Support for Canon printer: Printing Issues on Canon imagePROGRAF Large Format...

Support for Canon printer: Printing Issues on Canon imagePROGRAF Large Format...: A number of users may come across problems printing from Vectorworks to Canon's imagePROGRAF line of large format printers. This proble...
Read More...

Any Kind of Canon Printer Problems Call Us
+1-855-517-2433 (Toll Free)

How To Service My Printer - Error Code for Canon PIXMA MP287

P02 – Carriage Error, there is something wrong with your printer ink cartridge, it could be in wrong position, something blocked the chip (see at the back of cartridge), also P02 error code show sign that your print head is broken or faulty, try to take out both of the cartridge and then put it back.

Read More...

P07 – Ink Absorber Is Full or Almost Full, you need to reset your printer, here is an article how to reset your canon mp287 printer. Follow the step, you can reset only if your absorber is almost full. You can’t reset if your ink absorber is full, to fix the absorber is full, you need to disassemble your printer and then replace the ink absorber (it’s just a pieces of sponge located in the printer), last time I just deep the sponge into water until the sponge is clean. I found a video but for MP258, the sponge located at the same position.

Read More...

Any Kind of Canon Printer Problems Call Us
+1-855-517-2433 (Toll Free)

How to Reset Error Code E08 in Canon MP287 - Absorber Full

When the MP287 is turned on, it will immediately appear on the LCD panel error E08 MP287. And when we do print command, then the monitor screen will show “The Ink Absorber is Almost Full”. Caption MP287 E08 error on the screen as follows:

1. Turn on the Canon MP287, MP287 LCD then the panel will pop up error E08, and there is a description of “The Ink Absorber is Almost Full” on the screen of your monitor.
2. Download Resetter MP287 at this link
3. Canon MP287 printer must be in a state of SERVICE MODE. Do I read the next step.
4. Canon MP287 Turn off the E08 error by pressing the power. Do not unplug the power cord.
5. Press and Hold the button STOP / RESET followed by pressing the POWER button. So both buttons depressed position.
6. Release the button STOP / RESET but do not release the button POWER.
7. In these circumstances the POWER button is still depressed, press the STOP / RESET 6 times.
8. Then release both buttons simultaneously. Then the Canon MP287 will be in Service Mode condition.
9. LCD Panel MP287 will blank / dark and in your computer will detect new hardware. Ignore it.
10. The next step Exctract and Run Service Tool for MP287 MP287 E08 error you downloaded earlier.
11. Click the “PLAY”, then the printer will proceed, then MP258 will print one page with the words “D = 000.0″
12. Click “Clear EEPROM”.

13. Then click “EEPROM”, and the printer will print the results MP258 Resetter. Writing one line as follows: “TPage (COPY TTL = 00 000 = 00 000)”.
14. Canon MP287 Turn off by pressing the power.
15. Canon MP287 printer that error E08 will be normal again.

Read More...

Any Kind of Canon Printer Problems Call Us
+1-855-517-2433 (Toll Free)

How to Install a Canon Printer in Mac Classic

Mac Classic is any version of Mac that came before Mac OS X, but it usually refers to Mac OS 9 and Mac OS 8 since they were the most recent operating systems before OS X came along. While all Mac OS X computers have printer drivers installed on them, most Mac Classic computers do not. To install a Canon printer on Mac Classic, it must be compatible with Mac OS 9 or lower and have an install CD.

      

Put the Canon printer install CD into your Mac and click the icon. Click on the "Install.pkg" to install the printer drivers on your Mac. Click "Continue" and then "Install."

Plug your Canon printer into an outlet and connect it to the Mac via the printer port or USB port. Turn the printer on.

Eject the disk from your Mac and open the "Chooser" in the Apple menu.

Choose the Canon printer's icon from the list and click on "Select a port."

Select the printer icon and click "Close." A new window will open prompting you to set up the printer.

Align your Canon printer following the directions on your screen and click "Close" when it is finished

Read More...

Any Kind of Canon Printer Problems Call Us
+1-855-517-2433 (Toll Free)